Video

Video

Bơm dầu suntec bơm cao áp suntec E7NC 10697P TA3C 40107 E6NC 10697P TA4C 40107 AJ6CC 1000 4Y D67A 72804 TA5C 30107 TA2C 40107 AJ6CE 1013 4Y ASU67A 74024 E4NC E4NA E7NA

Liên hệ

  • Mã sản phẩm
  • Tình trạng:
  • SUN02
  • 5
Số lượng: Mua hàng

Bơm dầu Suntec E7NC 10697P TA3C 40107 E6NC 10697P TA4C 40107 AJ6CC 1000 4Y D67A 72804 TA5C 30107 TA2C 40107 AJ6CE 1013 4Y ASU67A 74024 E4NC E4NA E7NA dùng cho dầu FO dầu diesel xuất xứ Pháp hàng luôn có sẵn và giá rất cạnh tranh.
Nguyên lý hoạt động của Bơm dầu Suntec:
Bộ bánh răng hút dầu từ bồn dầu và chuyển nó đến van điều chỉnh áp suất dầu đến đường ống. Tất cả dầu không đi qua bec phun sẽ đi qua van dầu hồi và theo đường ống dầu hồi trở về nếu hệ thống có hai đường ống dẫn dầu hoặc, nếu nó chỉ có một đường ống, dầu sẽ quay trở lại bộ bánh răng
Hiện tượng lọt khí :
Đầu ren của vị trí gắn đồng hồ đo áp lực phải được nới lỏng cho đến khi không khí được thoát khỏi hệ thống. Đảm bảo dầu điền đầy trong bơm, giúp bơm vận hành tốt. 

Cấu tạo bơm dầu Suntec dòng TA

APPLICATIONS
- Heavy oil.
- One or two-pipe system.
- Pump associated with in-line solenoid valve to assure cut-off function.
 
PREHEATING  FACILITY
The body of the E 1069 unit  includes a drilling to accept an electric preheater. This cavity has been designed to give maximum heat transfer from the heater to the oil in the pump without there being direct contact between the heater cartridge and the oil.
The heating cartridge can be fitted either by right-hand side or by left-hand side.
The preheater should be connected for a period of time prior to starting the pump.
When the right temperature is reached, it can be switched off or left permanently
switched on to maintain fluid oil in the pump during the periodic burner shut downs.
The oil supply, pipes and filters must be separately heated.
 
PUMP  OPERATING  PRINCIPLE
The gear set draws oil from the tank through the built-in filter and transfers it to the valve that regulates the oil pressure to the nozzle line. All oil that does not go through the nozzle line will be by-passed through the valve back to the return line in two pipe installation or, if it is a one-pipe installation, back to the suction port in the gear-set.
In that case, the by-pass plug must be removed from the return port and the return port sealed by steel plug and  washer.
Bleed :
During the starting period, air is purged through the nozzle line : the by-pass hole of the nozzle plug allows air to pass to the nozzle line without opening of the regulator valve.
For the first start up, bleeding can be accelerated by loosening the plug in the
pressure gauge port.
Note :
Due to the presence of the by-pass drilling in the nozzle plug, there is no cut-off.
Cut-off must be provided by an external solenoid valve.
This drilling prevents high pressure building up in the nozzle line due to expansion of oil from residual heat in nozzle line oil heaters during shut-down periods.
 
Cty Kỹ Thuật Phát Đạt chúng tôi chuyên nhập khẩu, lắp đặt ...các loại bơm dầu suntec trên toàn quốc. Hàng chất lượng tốt, giá cạnh tranh, có CO, CQ, hàng có sẵn nên giao hàng nhanh


Giá tốt
Hàng có sẵn, giao nhanh trên toàn quốc
Quý khách vui lòng liên lạc.
Số điện thoại   0989286139,  0906363933, 0975052273 , 0906363933, 0966485673
Email:  info@phatdatcompany.com
Web: www.phatdatcompany.com
YouTube: https://www.youtube.com/channel/UC6b-Js97gd9-JgfVwwN-Dgw 
 



Sản phẩm liên quan